Setting Up A Specification For Annual Roof Repair



Keep in mind that these methods are considered temporary fixes. The only permanent solutions to a leaking roof is a professional repair or replacement. But, depending on the age of your roof and the overall condition, this may help to buy you some time.


You may not be able to seal the leak right away, especially if it’s raining and wet. Roof patch will not hold in wet conditions until it’s had time to cure.

  • You need to provide a path for the water to drain. The easiest way to do this is by sticking a nail into the hole. It will attract the water to it, and allow it to funnel in one direction.
  • Place a large 5-gallon bucket under the area to catch any water that drains. Make sure the bucket is large in case it fills quickly.
  • Wait until the area is dry enough to seal the leaking area.


If the damaged area is already dry, you don’t need to use the above trick for diverting the water. You can go on to this step of sealing the leak. If it has been raining, then you must wait for things to dry out before you can seal it.

  • First, you must identify where the leak is coming from. The best way to find the source of the leak is to go into the attic or crawl space above the home.
  • Next, take a flashlight and shine it around check for areas of dampness. These are usually easy to find because moisture causes darkness and mold.
  • Using marking chalk, draw a circle around the area that is problematic. This marking will help you to identify the problem when you make a more permanent repair.
  • The area must be dry to use the roof patch. Once it’s dry, apply a liberal amount of the roof patch to the leaking area. Use a scraper to spread it evenly, and ensure the entire region is covered.
  • Once the roof patch has dried, use caulking to cover the edges and any holes that appear. You can use your finger to make sure you get the caulking spread around to the entire area.


Enter into The Attic

To fix your leaky roof, look for the attic of your house and enter inside. Clear insulation from the wet ceiling wall and dry off any standing water. To do this, you can put a small piece of plywood across the joists of your ceiling and then place a bucket on it to catch the water.

Locate the Leak

Find the leak by following the position at which it enters your roof. At times, it can be quite a distance from the spot where it is dripping onto your ceiling. You can certainly trace the path along a beam, but at times water can follow the base of the roof deck.

Make a Transient Patch

The next step is to make a transitory leak patch using roofing tar and plywood or a piece of shingle. Apply the roofing tar onto the leak on the base of your roof deck, utilizing a putty knife. Press the plywood or piece of shingle on the roofing tar and add more tar round all the edges of the leak patch.

Measure the Leak’s Distance

While you are still at the attic, measure the distance of the roof leak from the ridge and the gable as well. By doing this, you will be able to trace the leak once the rains are over. Once the rains let up, you can go back to your roof and measure similar dimensions, and then fortify the base of the shingles surrounding the leak with more tar.


How to Repair a Leaky Mobile Home Roof

Mobile home roofs tend to leak because of changes in temperature and harsh weather conditions. You will know your mobile home has a leak if you see ugly stains on your ceiling. It is important to repair the leaky roof before fixing the stains caused by the leak in your home. Many times it is difficult to identify where the roof leak is located because the hole may be a tiny space between the flashing and the roof. You will need to check your entire roof thoroughly and use the necessary materials to repair the leak.

Step 1

Use a ladder to climb up to the roof. Make sure to walk on the rafters, and inspect the gutter system, flashing, seams, seals and shingles for leaks.

Step 2

Remove all dirt from the area to be patched by scraping the area with a putty knife. Put strips of butyl tape in a square around the perimeter of the area to be patched.

Step 3

Use tin snips to cut out a patch of galvanized metal that will overlap the leaky area by 3 inches on all sides. Place the metal patch over the butyl tape.

Step 4

Predrill holes in the galvanized metal patch, as well as the roof. Use metal screws to screw through the patch, butyl tape and roof metal. Place the screws every 2 inches around the perimeter of the patch.

Step 5

Apply caulk to seal the edges of the patch and the screws. Once it dries, cover with a roof coating.


How to Stop a Roof Leak in the Rain: Preparatory Phase

Clean Up Leaking Area Fast

How to stop a roof leak from the inside? Make sure the area underneath the leaks is clear of water. If you can anticipate leaks by knowing their telltale signs, you can make early preparations that prevent further internal damage.

You can do the following to clear up rooms with leaking roofs fast:

  • Use a mop and pail: Run the mop along the drenched floors. Then, squeeze the leak water into the pail. Perform the same for all ceiling areas and leak-infiltrated rooms. Lastly, place pails to catch further rainfall in the rooms.
  • Suction Hose: If leak water has submerged a room one foot or above, use a suction hose that leads straight to your sewer system to get rid of water fast. Next, clear the room with a mop and pail. Don’t forget to catch the roof leaks with pails too.

Move Furniture and Appliances

If you want to know how to stop a roof leak in the rain, you’ll need to trace its original path. To do this, you’ll need to move all your furniture and appliances outside of leaking rooms. You can’t stop roof leaks without the water destroying your furniture and appliances. Move all furniture and appliances into non-leaking rooms. Furthermore, move a high-powered heater inside these rooms to assist in drying all your belongings.

If you cannot move the furniture or appliance for any reason, you can use thick plastic material to cover its top and underside. Unfortunately, rooms with high likelihood of leak submersion will damage your appliances severely. On the other hand, a water removal and reconstruction service is more expensive than just limiting your expenses on roof repairs. So, prioritize leak repairs first!

Do The Same for The Other Rooms

If you have many leak-infiltrated rooms, perform the same methods we shared above. It is imperative you do this quickly. The more time leaks stay, the bigger the leak source becomes over time. You can assign family members to do steps one and two in different rooms to save time. As an alternative, you can use rags instead of mops to hasten the process. In addition, you can use any container type to catch leaking water from your roof.


PE Plastic Covers

As an alternative, you can use polyethylene plastic to cover leaks. This is especially useful if you can’t identify the roof leak source. If you want to know how to stop a roof leak in the rain swiftly, always have PE plastic handy with you.

True enough, your roof vent leaks during heavy rain along with other roofing structures. Pulled flashing is a common reason for internal leaks through your chimney, skylights, and others.

If you want to know how to a stop roof leak in the rain with PE plastic, proceed further below.

First, unroll the plastic. Then, use a measuring tape or ruler to approximate the right amount of PE plastic to cover the leaking area. Additionally, always add at least an extra four feet to your exact measurements to give allowance for heavy downpour leaks.

Next, use a staple to attach the thick plastic. Lastly, nail the positions into place for additional PE plastic reinforcement.

What Differentiates Commercial Roofing Companies From Residential Roofing Companies

Tips When Selecting A Commercial Roofer for Your Property

Your commercial roofer should have the proper licenses, certificates and affiliations.

They must provide proof that they are licensed to practice in your state and that all paperwork is up to date. This includes having insurance, worker’s compensation and liability coverage. These things are vital if there is ever an accident while they are performing work on your property. It’s also important that all employees who will work on your commercial roof be trained and certified, not just the owner. Additionally, since it’s a commercial building, you are subject to regular inspections and you need to know that you have done everything possible to ensure your roof is sound and will pass these inspections. You can find information from the department of licenses in your state. Get copies of all paperwork to protect yourself and your company.

Ask for referrals.

Every company will say they are the best but the only real proof of that is a satisfied customer. You can ask friends, business associates and other businesses in your area. To get an accurate idea of what your experience with the commercial roofer will be like, make sure that the referral has had work done recently and that their building is similar to yours. Also, remember to ask about friendliness of staff, how well they communicate and whether follow up work was needed before the job was done satisfactorily. Be sure to ask for a portfolio of their previous work. You can also ask the company for a list of references. Don’t just ask for the list; take the time to actually call each one.

Make sure they have expertise in all commercial roofing matters.

It would be a hassle if you have to hire multiple companies to work on one roof. For instance, if you have an older roof, you don’t want a commercial roofer who has no experience handling all the issues associated with this kind of roof. That means they will likely have to subcontract the job to different companies, leaving you at risk for mistakes and problems that can arise from working with unknown companies.

Remember that the lowest bidder is not always the greatest value.

In your desire to save money, it’s tempting to select the company with the lowest estimate. However, beware. Some of these companies use subpar materials and cut corners in order to outbid competitors. This will end up costing you more money in the long run and, in extreme cases, can lead to total roof failure.

on’t rely only on referrals and advertisements.

While the business down the street might have had a good experience, that doesn’t mean the roofing contractor is top quality. After all, any company can get it right once. Flashy, expensive ads are also not the best indication. It’s vital to do your own research. Check with organizations like the Better Business Bureau and online review sites such as Angie’s List to find out if there have been any major complaints about the roofing contractor before you make a final decision. If you do see complaints, you should pay attention to patterns. There may be a customer or two with an ax to grind so they write a bad review. However, if you notice several reviews that all criticize the company’s slow response time or missed appointments, that should tell you a lot about how they operate and you may want to choose a different company


Tips For Choosing Commercial Roofing Contractors

Do your homework

Checking out your options before hiring a roofing contractor to service your company building is important. Inquire about a perspective roofer’s background, whether or not they are licensed and insured, how long they have been in business, etc

Ask around

Many businesses obtain a majority of their work through word-of-mouth, which can be a great way for you to find a reliable roofing company. Ask other businesses in the area to recommend a good Atlanta roofer, which will make your search easier.

Ask for references

Asking for references is a good idea and if a commercial roofing company hesitates to provide you with references upon request, then you should steer clear. A reputable roofing company will not hesitate and will be proud to provide you with former customers who can vouch for the quality of their work

Check with the BBB

Although not all businesses are members with the Better Business Bureau, it’s a good idea to check with this agency before hiring a company. Even if a company isn’t listed, there could still be complaints that have been filed with the BBB, which could be helpful when it comes to ruling out perspective commercial roofers.

Request portfolios

It might be a good idea to ask to see portfolios of work that perspective roofers have done in the past. A professional commercial roofer will be proud to show off his or her work and this can help you narrow down your possibilities further.


Tips on Choosing Good Commercial Roofing

It is vital that you provide your investments with ample protection against harsh climate. That said, it can be challenging to decide which roof would best provide you with the peace of mind that you need.

Choose a Durable Roofing Material

There are many kinds of commercial roofing in the market and it can be confusing to pick the one that you can truly rely on. When it comes to roofing, however, you can never go wrong with choosing a durable product. Apart from water restoration in Lincoln, NE, we offer thermoplastic roofing that is resistant to extreme temperatures and can last for 20 years. These can also withstand strong winds and punctures, despite unpleasant weather conditions.

Choose an Energy-Efficient Roof

It can be tricky to manage your company’s budget. As much as possible, you want to save and earn more than you spend. Fortunately, we offer PV solar panels that can help you do just that. These roofing systems absorb sunlight and use it to generate energy for your business. These help keep your energy costs low while promoting comfort in your workspace.

Choose the Right Commercial Roofing Company

The performance of your roofing is only as good as the contractor who installed it. We take pride in being one of the few GAF-certified Master Elite™ contractors in the region. Besides commercial construction in Lincoln, NE, we also offer roofs that come with strong warranties, which will protect you from poor workmanship. We have years of experience in handling roofing concerns. Our partnership with leading brands is proof that you can expect to receive excellent service from us.


Tips for Choosing the Best Commercial Roofing Contractor

In cities and urban areas, where business thrives, commercial roofing is prevalent. Roofs protect homes and commercial buildings. Other than securing a building from harmful sun rays, excess rain, and storm, it also adds to the overall look of the building.

Tips for Choosing the Best Commercial Roofing Contractor

A commercial roofing contractor is your guide to a beautiful and lasting roof. If you don’t know one, it is time to connect with a commercial roofing company. Selecting a contractor is not easy. Today, with multiple options available online, you should choose wisely.

Always Search Locally First

Online you will come across impressive roofing contractor websites, located outside your region. Everyone wants the best commercial roofing for their office building. Hence, it’s natural to get tempted to speak to these companies. But before you do so, realize that a roofing installation doesn’t end when the roof gets installed.

Ask for Recommendations

You must offer your commercial roofing project to a contractor, who has adequate know-how and experience. It is wise to ask for personal recommendations. You can get talking to your friends, family members and colleagues

Ask for Valid Work Permits and License

It is essential for a roofing contractor to carry a legitimate work permit in your area as well as legal license. It’s not safe to trust a contractor who is working without keeping the legal documents on place.


Things to Look for When Choosing a Commercial Roofing Company

Your roof is your business’ first line of defense. It works day and night to protect your business property against the elements and intruders. That is why it’s so important that you take care of any issues as soon as disaster strikes. Whether it’s just a simple leak or a severely damaged roof, you need a professional who will provide high quality work that is guaranteed to last. But finding a reputable commercial roofing company can be challenging. Many businesses don’t have your best interests at heart, and are only interested in quickly turning a profit. Failing to properly screen a company you hire could leave you paying more than necessary or receiving low quality service.

Look locally: The best contractor will not only have a local location, but also an established reputation within your community. Unfortunately, some fly-by-night businesses will be out of sight long before your roof’s standard five-year warranty period comes to an end. The warranty is only good if the company will honor it, which is why it’s so important that you choose someone you know will be there when you need them.

Consider experience: Roofing is hard work. A high quality roofer will have years of training and on-the-job experience. This knowledge prepares them to deal with any situation that could arise during commercial roof repairs in Dallas, TX.

Always ask for recommendations: Ask your friends and family for recommendations. They will be able to provide you with honest insight into any companies they have used in the past and whether their work has stood up to the test of time. This will provide you with the best picture of a company’s customer service and workmanship

Insurance isn’t debatable: Never consider a roofing company that doesn’t carry worker’s compensation and liability insurance. Always ask to see the certificate, and call their insurance carrier to confirm it is still valid. Without this, you could find yourself facing thousands of dollars in unexpected costs if something were to go wrong.

Must Learn How To Do Roof Installation

What You Must Know About Torch Down Roofing Installation

What is a Torch Down Roof?

Torch down roofing (sometimes referred to as “torch on” roofing) is so named because it requires an open-flame propane torch. In this installation method, sheets of modified bitumen are rolled out onto the roof, and a roofing professional uses a hand-held propane torch to heat the material and adhere it to the surface. Once the layers reach the right temperature, seams are melted together to create a waterproof seal.

The membrane layers of a torch down roof are made of an asphalt compound called bitumen that is modified with either rubber or plastic. The main strength of this type of roofing is that it can expand and contract without melting or cracking. It has a high tolerance for both the heat and the cold it will experience on the roof during the change of seasons. There are different types of torch down roofing including two-layer and three-layer systems.

If you’re wondering whether torch down roofing is the right choice for your flat roof, you can learn about the pros and cons of torch down roofing from this article. We’ll also cover the details of the materials and layers that are used to create a torch down roof.


What is Torch Down Roofing Material?

Torch down roofing comes in the form of rolled sheets. Your roofing contractor will unroll each sheet individually during the installation process (two sheets for two-layer, three sheets for three-layer).

Each sheet of torch down roofing material consists of multiple membranes stacked and adhered together. These are the membrane layers of torch down roofing material, from the bottom up:

Layer 1: Thermo-fusible film.

Layer 2: Modified bitumen.

Layer 3: Reinforced polyester.

Layer 4: Modified bitumen.

Layer 5: (For the third layer of a three-layer roof) Granulated mineral surface.

A compound known as modified bitumen makes up the second and fourth membrane layers of each sheet of torch down roofing material. Bitumen is an asphalt compound. It is used in roofing and other construction applications like road construction and repair. Modified bitumen is asphalt bitumen mixed with a plastic or rubber additive. There are two main types of modified bitumen membrane that are used to create torch down roofing material: Atactic Polypropylene (APP) and Styrene Butadiene Styrene (SBS).

Atactic Polypropylene (APP)

APP is a type of plastic used to produce modified bitumen for torch down roofing. APP modified bitumen membranes are especially flexible. They respond well to both high and low temperatures.

Styrene Butadiene Styrene (SBS)

SBS is a type of rubber used to create modified bitumen for torch down roofing. SBS modified bitumen membranes are also flexible, and they have a lower melting point than APP membranes. This means that SBS membranes can be used in torch down roofing, as well as self-adhering and cold-processed roofing systems.



A torch roof is applied with propane and a torch. When a full 3’x 33’ roll has been installed, the next roll is set next to it with a 4” overlap. It is then heated and “kicked out” just like the first roll. An overlapping seam is then created. This seam is “welded” together by applying enough heat to bond the seam and create a “bleed” of liquid material from the roll. This is the factory recommended procedure. If too much heat is applied on this seam, the product becomes damaged and will crack at the point where it was overheated. Water will then begin to leak into the crack in the seam. If not enough heat is applied to the seam, a welded bond will not be created and the seam will leak.

With as many feet of welded seaming done on a typical roof, it becomes highly probable that at least a few feet of these seams will be over or under heated due to human error. Failure of just a few feet of seams will spell disaster for a roof that can allow the migration of infiltrated water. Irreversible damage to the roof system is likely to occur long before water is noticed entering the building.


Coating your torchdown roofing.

For extra protection you can let your torchdown roofing settle for between a month and two months before coating it with an extra coating that will make it even more fire resistant and increases the protection from heat by further reflecting the sun’s rays.

Other uses for modified bitumen.

This durable, hardwearing combination of asphalt and rubber resin isn’t only designed for use as torchdown roofing either and is used to great effect on basements, verandas, foundations and garages. If you have a need for a weather resistant, flexible but very strong covering then torchdown roofing is the solution you have been looking for.

The cost of torchdown roofing.

The overall cost of torchdown roofing will ultimately depend on the roofing contractor you use to complete the work and the price of the actual components; however, it is only slightly more expensive than traditional asphalt roofing. In exchange for the small amount of money extra you receive roofing that is more resistant to weather and less likely to become damaged. This means that over its life it will cost you less in roof repairs; it really does work out cheaper in the long run to have torchdown roofing over asphalt roofing.


How to Remove Old Flat Roofing

Flat roofing has some advantages, but when it ages or falls into disrepair, it can be troublesome. Leaks form and the materials erode into something that is better off being replaced than fixed. Eventually the time comes when you need to simply remove the old flat roofing material and go with a new product. To save you some time and money, this is a project you can do yourself. Flat roofing is typically asphalt material, similar to that of standard shingles, but applied in long strips, approximately 18 inches wide and referred to as rolled roofing.

  • Check your dry roof for safety. Use stable ladders or scaffolding to get on top of the roof and ask someone to assist you. Someone else should be around in the event of a fall. Walk on the roof carefully to check it for stability and look for any places where it might not be safe to tread. Once you have determined that the roof is safe for working on, you can move on to the next step.
  • Pull a pickup truck or move a dumpster to a convenient area just beside the house. As you remove the old roofing material it will need to be disposed of. You should not leave any of it on the roof because it could become a tripping hazard. As it is removed, the material should be tossed over the edge of the roof and into the bed of a truck or into a dumpster for proper disposal.
  • Remove the gutters from the perimeter of the roof. On a flat roof it is possible you’ll need to remove gutters. Some flat roofing may not have standard gutters, but many will. In order to get to the edge material, these gutters will need to be taken down. Clips hold on many newer plastic gutters that you’ll be able to unlatch by hand. Older metal gutters could require the use of a screwdriver to loosen the attaching screws. After the gutters are down, also remove the fascia board if applicable.
  • Sweep off any chipping material that is on top of the roofing. Many flat roofs are covered with a scattering of chippings, often gravel, that need to be swept up and bagged for re-use before removing the roof.
  • Use a wrecking bar or roofing shovel to pry up the edges of the roofing sheets. Once you get under the edges with the tool, simply thrust forward and rip the material off the roof. It could take some considerable force, but you should be able to do with without any other tools or machines. As the pieces come up, toss them into the disposal bin or truck parked next to the building and continue to the next piece. Repeat until the roof is stripped of the material.

Tips To Make Residential Roofing

Top Roofing Tips

Think Safety First

Fussing to try and find a leak as soon as it happens is something that could put you in the hospital. Meddling on a roof while it’s raining or covered with ice and snow isn’t the ideal way to find a leak. Trying to temporarily fix a leak could be highly dangerous. If you want to do it right, there is no quick-fix. Just take your time, and be very patient and careful to wait for Mother Nature to give you the green light.

Take Precautions

Being on a roof will put the body in positions that are not comfortable or safe. Make sure to wear rubber sole shoes to prevent slipping. Also use a harness and always work with a buddy.

Spray the Roof

Take a garden hose and go up to the roof and start spraying in different locations to find the leak. Wait if it’s wintertime because it’s not safe to run water on the roof when it’s freezing out.

Keep Gutters Clean

One of the most common areas and causes for roof leaks are clogged gutters. Gutters that have not been cleaned can cause the water to build up during rain.

Avoid Dry Rot

Dry rot isn’t related to any type of water damage, but lack of ventilation. If a roof repair is right in the middle of the roof, there is a chance that the plywood might be deteriorating. The roof will actually sag in and cause the roof shingles to get brittle, crack and then leak. Preventing dry rot consists of installing a ridge vent, which will only work if there is a soffit vent. Holes have to be drilled through the soffit vents so cool air comes in through the bottom and pushes the hot air out through the top.


Roofing: Replacement or Repairs?

As an Portland homeowner, you may not look forward to regular roof maintenance, but if you want your roof to live up to its full potential, hiring a roofing contractor for a roof inspection is a wise decision. Homeowners should have their roofs inspected at least once a year, and severe weather may necessitate more inspections because rain, hale, snow, and wind can damage roof shingles and tiles, cause premature aging, and create leaks. Roof inspections allow a professional to examine your roof for complications that may otherwise go unnoticed.

What Does a Roof Inspection Entail?

A roof inspection with your roofing contractor will include many examinations and an overall assessment of your roof. The inspector will search for weather damage, granular loss, debris, cracks, ponding, blisters, water staining, deformations, leaks, and corrosion. The inspector will also check the state of your skylights, chimney, and gutters.

How Does a Roof Inspection Prevent Roof Problems?

If you haven’t experienced any problems regarding your roof, you may just not be aware of current damage and the complications that will surely follow. Roof inspectors are trained to look for signs of damage, so they are able to find areas of concern that you may not spot. Your roofing contractor may notice improper ventilation, shingle granules in rain gutters, missing or loose shingles, and sagging near ridges or between rafters. Gaps in the flashing, pools of water, and leaks may also be present on your roof. All of these problems may appear minor at first, but they can result in severe damage that compromises the integrity of your roof and leaves it susceptible to pests, mold and mildew, and collapse.

Think of roof inspections as an investment in your home because your property value is likely to increase when your roof is in good condition. You will also avoid expensive repairs by hiring a roof inspector to examine your roof regularly. When the time comes to check your roof for damage, contact RJ Ramos Roofing, a reputable Portland roofing contractor.


Tips to Help Homeowners Choose the Right Roofing Contractor

The biggest obstacle homeowners face when looking to fix or replace their roof is choosing the right person to do the job. After a damaging storm, they need to quickly get back to normal and perform the necessary roofing repairs. But that doesn’t mean they should just choose the first contractor who knocks on their door. Finding a contractor who is trustworthy, honest, and professional may sound difficult – but that’s where you come in. Contractors should share these 10 important tips with homeowners to show them that your company is reputable and can be trusted to protect their home and their wallet.

Get local referrals. There is less chance of potential issues or scams when you choose a contractor from your community. They are more familiar with local rules and code regulations and have a relationship with area crews and suppliers.

Look for manufacturer designations. Manufacturer designations are considered a badge of honor because the contractor must pass certain minimum requirements to be factory-certified (although, some manufacturers have more stringent requirements than others). GAF strictly enforces their top designation by only allowing 2% of roofing contractors per market to be recognized as profesional. (Unlike other manufacturer designations, profesional cannot use this top designation in another territory, only in the location of the storm.

Research Better Business Bureau (BBB) ratings. Some contractors blow in (no pun intended) right after a storm looking for work, so it’s important to look them up on the BBB website and make sure they have a good score. Stay away from contractors who do not exist on GAF profesional are required to maintain satisfactory ratings with the BBB in order to retain their certification.

Get an extensive warranty. Not all contractors can offer manufacturer warranties that include coverage of the contractor’s workmanship. If a contractor installs the roof incorrectly, it may take months or years for the damage to show up—and insurance won’t pay for it. If the contractor won’t fix it (or worse, has gone out of business), your only recourse is to pay for their mistake yourself. A profesional can offer one of the longest workmanship warranties on the market.


Roofing Tips That Can Help You Out

There is a ton to know about roofing. All of this can be overwhelming, and that’s why it’s so important to have lots of good advice in one easy to read place.There are a lot of great roofing tips in the article below.

Make sure that your roofer you choose has liability insurance. The main thing that this will show you about a policy bodes well for a contractor’s reliability.Secondly, should something happen to your roof as they are working on it, their insurance company would cover the costs.

Don’t use short-term solutions for short periods of time when dealing with roof repairs. It may seem cost effective at the time, but in the end, and that may cost you more. The best thing to do is to completely fix the problem as quickly as possible to prevent things from getting worse.

When you have your contractors narrowed down, check with each with regard to their warranties. You want a warranty that lasts for at least 3-5 years. It must cover workmanship and defective supplies, plus they should give you copies of all manufacturer warranties as well.

Residential Roof Repairs

Make sure any roofer you employ has the licensing necessary to do the job. Do not simply believe that he is legitimate based off what is required.Contact your local building department and see what is needed.

Make sure a roofing contractor has current, and make sure thy are current.Just about every locale requires roofers to be licensed, so be sure they have a valid and current license.

A good team can achieve good results more quickly.

Only hire a roofing contractor for roof repairs Dublin that is able to supply you with proof of current insurance and insurance.

Ask contractors about their memberships in industry associations. The good contractors join industry groups to stay informed on the latest technological advances and improvements to standard techniques. If your roofer is not, question their level of dedication to the field.

It’s very important to catch damage to the shingles are replaced as soon as possible. Look over your roof, but do so safely.


Tips To Maintain Your Roof

Proper roof maintenance requires regular inspections. Seasonal or yearly checkups will lengthen the life of your roofing materials, preventing leaks that lead to damage, costly repairs, and — horrors! — the necessity for a complete roof replacement.

We decided to put together a quick list of roof maintenance tips that will alert you to any problems and help extend the life of your roof.

Roofs are designed to weather (literally) all kinds of storms, but there is going to be some wear and tear. So be sure your roof is ready for the next big storm by following these helpful tips on roof protection.

If you have any questions about roofing repair, damaged shingles, roofing home improvements, or your roof system in general, please call Pacific West Roofing. We’re happy to guide you through the best solutions for you and your home.

Inspect Your Shingles

Do yearly checks on your roof shingles — especially after the wild weather months. But remember: It’s not just wind and wet that can damage your roof. Ultraviolet light from the sun’s rays can also wreak havoc over time. So be sure to examine your shingles as a regular part of your roof inspections to ensure they’re still installed properly and functioning as they should.

Trim Branches

If you have trees with overhanging branches, have them trimmed before the winter sets in. Heavy snow, wind, ice and other natural phenomena can whip branches around or pull them from the tree completely, causing damage to the root and the structures on top of it.

Unclog Gutters

Many of us are familiar with the problems associated with clogged gutters, which can include bubbling wall paint and rotting wood. But clogged gutters can overflow with so many leaves, bugs, and debris that the rain washes up instead of down. Over time, the water can damage the roof and the support beams that hold it aloft. You can imagine the kind of problems that will cause: the expensive kind. Clean your gutters and clean outs heading into the spring and fall seasons.